How to Make Your Own Wrist and Ankle Weights

How to Make DIY Wrist and Ankle Weights

The Spruce Crafts / Mollie Johanson

Project Overview
  • Total Time: 2 hrs
  • Yield: Pair of weights
  • Skill Level: Beginner
  • Estimated Cost: $20

Wrist and ankle weights are a great way to add some heft to your home workout or a brisk walk outdoors. This easy tutorial lets you make your own weights in almost any fabric you want and with whatever weight you need. Start with a pair of one- or two-pound weights then increase the size to make heavier weights as needed.

What You'll Need

Equipment / Tools

  • Scissors
  • Rotary cutter, ruler, and cutting mat
  • Sewing machine
  • Pins and sewing clips
  • Iron and ironing board
  • Chalk pencil or disappearing marking pen
  • Scale

Materials

  • 1/3 yard tightly woven cotton or nylon
  • 1 yard 1-inch-wide webbing
  • 24 inch snag-free sew-on hook-and-loop tape
  • 2 1-inch-diameter D-rings or rectangle hardware
  • 2 to 3  pound weighted filler (aquarium substrate, rice, sand, etc.)
  • Quality thread

Instructions

  1. Cut the Fabric and Strap Pieces

    Cut two pieces of fabric, 13 inches by 9 inches each.

    Cut the webbing into two 18-inch pieces. If you're using nylon webbing, carefully melt the ends of the sections with a hot knife tool or flame to prevent the webbing from fraying.

    Cut the hook-and-loop tape into two 12-inch pieces.

    Tip

    Snag-free hook-and-loop tape (Velcro) is soft, single-sided, and sticks to itself, making it perfect for this project. If you'd prefer to use standard hook-and-loop tape, work with two 6-inch sections of the matching sides.

    Measure and Cut the Fabric, Straps, and Velcro
    Mollie Johanson
  2. Make the Straps

    Fold over about 1 inch on one end of the first webbing section. Place a ring in the fold, then fold the end of the tape under. Sew across the fold to secure it. Fold the other end down about 1/4 inch and then fold it under and sew to secure it.

    Center the hook-and-loop tape on the webbing with the tape pushed up against the fold on the plain (non-D-ring) end. Sew around the tape.

    Repeat with the second strap.

    Tip

    If you're using strips of hook tape and loop tape, start with a 6-inch piece of hook tape, then place the 6-inch piece of loop tape next to it on the strap. Sew the edges and the ends of both pieces.

    Sew the D-Rings to the Straps
    Mollie Johanson
  3. Attach the Straps

    Mark the center point of the hook-and-loop tape. Position the strap so it is centered on the first fabric piece with the D-ring end 1-1/2 inches from one end and the marked tape center is 1-1/2 inches from the other end.

    Pin in place. Sew the strap in place by stitching from the folded section, along one edge, across the marked center of the hook-and-loop tape, along the second edges, and then across where you started. Backstitch to secure your stitching.

    Repeat with the second piece of fabric and strap.

    Sew the Velcro to the Strap and Sew to the Fabric
    Mollie Johanson
  4. Sew the Weight Body

    Fold the hook-and-loop tape in on itself so it's out of the way. Fold the fabric in half with right sides together. Pin and sew along the long edge with a 1/2-inch seam allowance.

    Sew the Fabric Into a Tube Shape
    Mollie Johanson

    Press the seam open, then center it on the sewn tube shape.

    Sew across one end of the tube with a 1/2-inch seam allowance. Backstitch each end, and be sure to sew all the way to the folded edges.

    Repeat with the second fabric piece.

    Sew the End of the Weight Closed
    Mollie Johanson
  5. Mark the Sections

    Turn the tube right side out. Measure and mark across the tube starting 3 inches from the sewn end, then at the 6- and 9- inch points. Use a marking tool that is easy to see, but also easy to remove.

    Divide and Mark the Weight Evenly
    Mollie Johanson
  6. Weigh and Fill the Sections

    Decide how much you want each wrist or ankle weight to weigh. Divide that amount by four—one for each section in the weight. Use a kitchen scale to weigh the filler. Be sure to take into account the weight of the bowl!

    Weigh and Divide the Weighted Filler
    Mollie Johanson

    Roll a piece of paper into a funnel shape and pour the first 1/4 of the filler into the weight.

    Tip

    Try to find a filler with a higher density so you get more weight for the volume. For example, 1/4 lb. of aquarium substrate takes less space than the same weight of rice or plastic pellets. Also, remember that if you use rice, you won't want to get the weights wet, so you'll need to be careful when cleaning them.

    Pour 1/4 of the Filler in the Tube
    Mollie Johanson
  7. Sew the Sections

    Tap all of the filler down and use pins to hold it away from the first marked line. Sew across the line from edge to edge, backstitching at the beginning and end.

    Add each portion of filler and sew across the lines to close the sections.

    Sew Across the Marked Line for the First Section
    Mollie Johanson
  8. Sew the End Closed

    When you add the last portion of filler, fold the open end in 1/2 inch. Pin or clip the end together, keeping the filler away from the end.

    Fold the End in and Clip in Place to Sew
    Mollie Johanson

    Topstitch across the end, sewing 1/8 inch from the edge.

    Repeat the filling and sewing for each weight.

    Sew the End of the Wrist/Ankle Weight Closed
    Mollie Johanson

To wear the weights, wrap them around your wrists or ankles and slide the strap through the ring. Fold the strap down and attach the hook-and-loop tape. When wearing them on your ankles, try placing them so they are more open at the front to give your feet more mobility.

Securing the DIY Wrist and Ankle Weights
Mollie Johanson

This size weight works best with a maximum of 1 lb of filler per weight, but you can adjust the size to accommodate more weight. Try increasing the fabric to 13 x 11 inches or lengthening the strap.

Use your weights during a workout, on a walk, or simply to add some resistance during daily tasks.

DIY Wrist Weights Sewing Project
Mollie Johanson